Chinese translation for "weld residual stress"

焊接残留应力

Related Translations:

residual relay:  零序继电器

residual buoyancy:  剩余浮力

residual liquor:  残留药液残余熔浆

residual swelling:  残余膨胀

residual realization:  余值实现

residual deviation:  剩余罗差剩余偏差剩余自差

residual immunity:  残留免疫残余免疫

residual oxide:  残留氧化物

residual capacitance:  剩余电容

residual stability:  残余稳定性

Example Sentences:

	1.	A new measurement method of welding residual stresses 一种新的焊接残余应力测量方法
	2.	The influence of the hydrotest on welding residual stress 压力试验对焊接残余应力的影响
	3.	An analysis of simulation of welding residual stresses in the t - joint 型接头焊接残余应力的有限元模拟
	4.	The influence of welding technics parameter to welding residual stress 焊接工艺参数对焊接残余应力的影响
	5.	Application of removing welding residual stress by explosion in guizhou aluminum factory 爆炸消除焊接残余应力在贵州铝厂的应用
	6.	Three - dimensional finite element analysis on welding residual stresses of construction steel 结构钢焊接残余应力三维有限元分析
	7.	Research on the vibratory stress relief used to reduce butt weld residual stress of dissimilar steel 振动时效用于降低异种钢对接焊缝残余应力的试验研究
	8.	Therefore one of efficiency means to solve cracking problem of runners is to change distribution of welding residual stress of blades , to decrease welding residual tensile stress in the dangerous area of blades or even turn to compressive stress 因此,改变叶片焊接残余应力的分布状态,降低叶片危险区域的焊接残余拉应力峰值,甚至将危险区域的拉应力转变为压应力,是解决转轮裂纹问题的有效途径之一。
	9.	In the analysis of the elastic local buckling strength of the plates in stiffened plates , an analytical expression is derived for calculating the local strength of a stiffened plate subjected to biaxial thrust considering plate / stiffener interaction and welding residual stresses and initial deflection 由于船体中的加筋板结构的受力情况是十分复杂的，除了主要受到由于总纵弯曲而产生的纵向压力以外，还会受到横向的压力以及垂向压力。
	10.	The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation . the result shows that welding residual tensile stress appears in the weld and its area nearby , and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding , and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time , heating temperature , heating area , and inversely proportional to cooling area , and welding residual tensile peak stress in the dangerous area is decreasing trend earlier , and then increasing trend later with heated location increased 本文利用数值模拟手段对转轮的焊接工艺从分段焊和局部加热两个方面进行了优化,结果表明:采用普通工艺焊接时,叶片焊后残余拉应力出现在焊缝及其附近区域,并且在叶片出水边的熔合线附近(危险区域)出现了峰值;在采用优化的分段焊时,先焊两端后焊中间的方法可以降低叶片危险区域的焊接残余拉应力峰值,降低效果与叶片出水边焊段长度、焊缝各段的焊接方向有关;局部加热法降低转轮危险区域残余应力的效果主要与加热时间、加热温度以及加热面积成正比,与冷却面积成反比,并且危险区域的残余应力随加热区域的增大呈先降低后升高的趋势。

Similar Words：

"weld quality monitor" Chinese translation, "weld range" Chinese translation, "weld rate" Chinese translation, "weld reinforcement" Chinese translation, "weld repairs" Chinese translation, "weld ripple" Chinese translation, "weld ripples" Chinese translation, "weld rod" Chinese translation, "weld roof" Chinese translation, "weld root" Chinese translation